NYUAD APRS

My position About ☰

reset

SQ9SIM-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9SIM-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1759596112	152 Count	38 Count	33 Count
1759592510	150 Count	38 Count	33 Count
1759588909	148 Count	38 Count	33 Count
1759585307	146 Count	38 Count	33 Count
1759581706	144 Count	38 Count	33 Count
1759578104	142 Count	38 Count	33 Count
1759574503	140 Count	38 Count	33 Count
1759570900	138 Count	38 Count	33 Count
1759567299	136 Count	38 Count	33 Count
1759563697	134 Count	38 Count	33 Count
1759560096	132 Count	38 Count	33 Count
1759556494	130 Count	38 Count	33 Count
1759552910	128 Count	38 Count	33 Count
1759549308	126 Count	38 Count	33 Count
1759545707	124 Count	38 Count	33 Count
1759542105	122 Count	38 Count	33 Count
1759538504	120 Count	38 Count	33 Count
1759534902	118 Count	38 Count	33 Count
1759531301	116 Count	38 Count	33 Count
1759527699	114 Count	38 Count	33 Count
1759524098	112 Count	38 Count	33 Count
1759520496	110 Count	38 Count	33 Count
1759516895	108 Count	38 Count	33 Count
1759513293	106 Count	38 Count	33 Count
1759509710	104 Count	38 Count	33 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: