NYUAD APRS

My position About ☰

reset

F6KNH-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F6KNH-14. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TX*	RX*	Digi*
1782747337	323 Count	139 Count	119 Count
1782745533	322 Count	139 Count	119 Count
1782743729	321 Count	139 Count	119 Count
1782741925	320 Count	139 Count	119 Count
1782740122	319 Count	139 Count	119 Count
1782738318	318 Count	139 Count	119 Count
1782736514	317 Count	139 Count	119 Count
1782732907	315 Count	139 Count	119 Count
1782731103	314 Count	139 Count	119 Count
1782729299	313 Count	139 Count	119 Count
1782727537	307 Count	138 Count	118 Count
1782725733	305 Count	137 Count	117 Count
1782723930	302 Count	135 Count	115 Count
1782722126	300 Count	134 Count	114 Count
1782720322	299 Count	134 Count	114 Count
1782718518	296 Count	132 Count	112 Count
1782716715	293 Count	130 Count	110 Count
1782714911	290 Count	128 Count	108 Count
1782713107	287 Count	126 Count	106 Count
1782686093	251 Count	109 Count	89 Count
1782684330	246 Count	109 Count	89 Count
1782682527	244 Count	108 Count	88 Count
1782680723	243 Count	108 Count	88 Count
1782678919	241 Count	107 Count	87 Count
1782677116	240 Count	107 Count	87 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: