NYUAD APRS

My position About ☰

reset

SQ6OXF-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ6OXF-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1766621155	324 Count	121 Count	109 Count
1766620255	323 Count	121 Count	109 Count
1766619354	322 Count	121 Count	109 Count
1766618453	321 Count	121 Count	109 Count
1766617553	320 Count	121 Count	109 Count
1766615751	318 Count	121 Count	109 Count
1766614851	317 Count	121 Count	109 Count
1766613950	316 Count	121 Count	109 Count
1766613049	315 Count	121 Count	109 Count
1766612149	314 Count	121 Count	109 Count
1766611248	313 Count	121 Count	109 Count
1766610347	312 Count	121 Count	109 Count
1766609446	311 Count	121 Count	109 Count
1766608546	310 Count	120 Count	109 Count
1766607645	309 Count	120 Count	109 Count
1766606744	308 Count	120 Count	109 Count
1766605844	307 Count	120 Count	109 Count
1766604943	306 Count	120 Count	109 Count
1766604059	305 Count	120 Count	109 Count
1766603159	304 Count	120 Count	109 Count
1766602258	303 Count	120 Count	109 Count
1766601357	302 Count	120 Count	109 Count
1766600457	301 Count	120 Count	109 Count
1766599556	300 Count	120 Count	109 Count
1766598655	299 Count	120 Count	109 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: