NYUAD APRS

My position About ☰

reset

SQ9ITQ-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9ITQ-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1781855194	568 Count	636 Count	72 Count
1781853393	567 Count	632 Count	72 Count
1781851593	566 Count	629 Count	72 Count
1781849792	565 Count	621 Count	72 Count
1781847991	564 Count	619 Count	72 Count
1781846191	563 Count	619 Count	72 Count
1781844390	562 Count	619 Count	72 Count
1781842590	561 Count	616 Count	72 Count
1781819197	548 Count	571 Count	72 Count
1781817396	547 Count	568 Count	72 Count
1781815596	546 Count	568 Count	72 Count
1781813795	545 Count	568 Count	72 Count
1781811995	544 Count	568 Count	72 Count
1781810194	543 Count	568 Count	72 Count
1781808393	542 Count	568 Count	72 Count
1781806593	541 Count	568 Count	72 Count
1781804792	540 Count	568 Count	72 Count
1781802991	539 Count	568 Count	72 Count
1781801191	538 Count	568 Count	72 Count
1781799399	537 Count	568 Count	72 Count
1781797600	536 Count	568 Count	72 Count
1781795799	535 Count	568 Count	72 Count
1781794000	534 Count	568 Count	72 Count
1781792198	533 Count	568 Count	72 Count
1781790397	532 Count	568 Count	72 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: