NYUAD APRS

My position About ☰

reset

SP6PAK-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP6PAK-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TX*	RX*	Digi*
1774778913	183 Count	844 Count	149 Count
1774777113	177 Count	788 Count	144 Count
1774775312	172 Count	761 Count	140 Count
1774773511	168 Count	721 Count	137 Count
1774771711	163 Count	695 Count	133 Count
1774769910	157 Count	668 Count	128 Count
1774768110	151 Count	638 Count	123 Count
1774766310	145 Count	613 Count	118 Count
1774764509	140 Count	589 Count	114 Count
1774762715	134 Count	562 Count	109 Count
1774760914	129 Count	539 Count	105 Count
1774759113	123 Count	515 Count	100 Count
1774757313	119 Count	494 Count	97 Count
1774755512	113 Count	469 Count	92 Count
1774751911	103 Count	425 Count	84 Count
1774750110	98 Count	403 Count	80 Count
1774748309	93 Count	376 Count	76 Count
1774746509	88 Count	353 Count	72 Count
1774744708	82 Count	331 Count	67 Count
1774742908	78 Count	311 Count	64 Count
1774741115	72 Count	286 Count	59 Count
1774739314	67 Count	263 Count	55 Count
1774737513	61 Count	238 Count	50 Count
1774735713	57 Count	217 Count	47 Count
1774733912	51 Count	195 Count	42 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: