NYUAD APRS

My position About ☰

reset

SP2OSA-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP2OSA-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1753255742	633 Count	161 Count	78 Count
1753254841	632 Count	161 Count	78 Count
1753253940	631 Count	161 Count	78 Count
1753253039	630 Count	161 Count	78 Count
1753251237	628 Count	161 Count	78 Count
1753250336	627 Count	161 Count	78 Count
1753249435	626 Count	161 Count	78 Count
1753248534	625 Count	161 Count	78 Count
1753247633	624 Count	161 Count	78 Count
1753246732	623 Count	161 Count	78 Count
1753245831	622 Count	161 Count	78 Count
1753244952	621 Count	161 Count	78 Count
1753244051	620 Count	161 Count	78 Count
1753243150	619 Count	161 Count	78 Count
1753242249	618 Count	161 Count	78 Count
1753241348	617 Count	161 Count	78 Count
1753240448	616 Count	161 Count	78 Count
1753239547	615 Count	161 Count	78 Count
1753238646	614 Count	161 Count	78 Count
1753237745	613 Count	161 Count	78 Count
1753236844	612 Count	161 Count	78 Count
1753235943	611 Count	161 Count	78 Count
1753235042	610 Count	161 Count	78 Count
1753234141	609 Count	161 Count	78 Count
1753233240	608 Count	161 Count	78 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: